Dave Embedded Systems SBC AXEL, Руководство пользователя

Страница: 131 / 139

S B C X U s e r ' s G u i d e v . 1 . 0 . 1
9 Appendices
9.1 U-Boot startup messages
The following messages will be printed on the serial console during U-
Boot startup (please note that messages may vary for different U-Boot
releases):
U-Boot 2013.04 (Jan 12 2016 - 15:51:23)-xelk-2.2.0
CPU: Freescale i.MX6Q rev1.5 at 792 MHz
CPU: Temperature 41 C, limits (-40 C, 125 C), calibration data: 0xc0
Reset cause: POR
Environment: SPI Flash
I2C: ready
DRAM: 2 GiB
Now running in RAM - U-Boot at: 8ff28000
NAND: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
CB ConfigID CRC mismatch for 0x00000000 (was 0x00000000, expected 0x2144df1c) at block 3 (offset 96): using default
Display: LDB-AM-800480STMQW-TA1 (800x480)
SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
In: serial
Out: serial
Err: serial
SOM ConfigID#: 00000003
SOM UniqueID#: df646299:0b0579d4
CB ConfigID CRC mismatch for 0x00000000 (was 0x00000000, expected 0x2144df1c) at block 3 (offset 96): using default
CB ConfigID#: ffffffff
CB UniqueID#: 00000000:00000000
Board: MX6Q-AxelLiteCB ConfigID CRC mismatch for 0x00000000 (was 0x00000000, expected 0x2144df1c) at block 3
(offset 96): using default
on XELK
CB ConfigID CRC mismatch for 0x00000000 (was 0x00000000, expected 0x2144df1c) at block 3 (offset 96): using default
Power: found PFUZE100 (devid=10, revid=21)
HW ver#: 0x1 (module_id)
CB ConfigID CRC mismatch for 0x00000000 (was 0x00000000, expected 0x2144df1c) at block 3 (offset 96): using default
unsupported boot devices
Net: FEC
Normal Boot
Hit any key to stop autoboot: 0
U-Boot >
9.2 U-Boot default environment
The following messages will be printed on serial console entering the
print
command from the U-Boot shell (please note that messages may
vary for different XELK releases):
addandroidargs=setenv bootargs ${bootargs} init=/init androidboot.console=ttymxc2 androidboot.hardware=freescale
addcons=setenv bootargs ${bootargs} console=ttymxc2,115200n8
adddisp0=setenv bootargs ${bootargs} video=mxcfb0:dev=lcd,${panel},if=RGB666
addhdmi=setenv bootargs ${bootargs} video=mxcfb0:dev=hdmi,1920x1080M@60,bpp=32
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off panic=1
fec_mac=${ethaddr}
addlvds0=setenv bootargs ${bootargs} video=mxcfb0:dev=ldb,${panel},if=RGB666 ldb=sin0
addlvds1=setenv bootargs ${bootargs} video=mxcfb0:dev=ldb,${panel},if=RGB666 ldb=sin1
addmisc=setenv bootargs ${bootargs} vmalloc=400M ${mtdparts}\\;${mtdparts_spi}
baudrate=115200
bootcmd=run usbrecovery; run mmcrecovery; run ${normalboot}
December, 2019
131/139