Datamax OC-2 series Скачать руководство пользователя страница 25

Страница: 25 / 27

OC-2 SERIES OF PRINTERS USER'S GUIDE

Agency Approvals

FCC Notice

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, it may cause harmful interference to radio

communications. However there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of

the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from
that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for
help.

Applicable Directive

•

89/336/EEC, 73/23/EEC

Applicable Standards

•

EN55022 (1998)

•

EN55024 (1998)

•

EN60950 (1992)

Содержание OC-2 series



























Результаты поиска

Содержание OC-2 series

Отзывы:

Похожие инструкции для OC-2 series

Бренды по названию

Популярные бренды

Datamax OC-2 series, Руководство пользователя

Результаты поиска

Содержание OC-2 series

Отзывы:

Похожие инструкции для OC-2 series

Бренды по названию

Популярные бренды