background image

 

B r o w s i n g   t o   t h e   P r i n t e r ’ s   I n t e r n a l   W e b   P a g e s  

 

Wifi Configuration Page 

 

Wireless Network 
Settings 

 

SSID 

Service Set Identifier that identifies the Module to connect to an AP. To make this 
connection, the Module and AP must have the same SSID. The SSID cannot contain 
spaces. Default setting is the MAC address of the wireless module. 

Wireless Network Type 

Specifies the type of network in which the Module will be used: 

    Infrastructure = connects to WLAN using an AP.  

    Ad Hoc = used to connect two peer-to-peer devices. 

    

Unique = resets card to Adhoc mode and uses the MAC address as the SSID 

(

default

Ad Hoc Mode Channel 

When Wireless Network Type is Ad Hoc, selects the channel used for communication. The 
two peer-to-peer devices must use the same channel. Range is 1 to 14 channels. Default 
channel is 1. 

Access Point Density 

Specifies a rate that, if not sustainable with the current association, causes the Module to 
look for an AP with which it can maintain the specified rate. A high setting causes the 
Module to more readily switch to another AP. 

    Low   

-    2 Mbps cannot be sustained. (

default

    Medium 

- 5.5 Mbps cannot be sustained. 

    High  

-  11 Mbps cannot be sustained.  

WLAN Region Code 

Module Operation Region 

Specifies the wireless channels allowed. This setting only applies when the Module is 
operating in Ad Hoc mode. The AP controls the channel used during Infrastructure mode. 
Default is US.

 

 

Wireless Security 
Settings 

 

Wireless Security Mode 

Configures the security settings.  
Disable   

security is disabled. (

default

wep64   

64-bit key length (sometimes referred to as 40-bit) 

wep128   

128-bit key length 

wpa-psk  

WPA Pre-Shared Key 

wpa-leap = 

WPA 

LEAP 

wpa-leap64 

Migration mode w/ Cipher suite TKIP+40 bit WEP using 
EAP(LEAP).  

Requires LEAP username and password

wpa-leap128 

Migration mode w/Cipher suite TKIP+128 bit WEP using 
EAP(LEAP). 

Require LEAP username and password

wpa-psk64 

Migration mode w/Cipher suite TKIP+40 bit WEP using WPA 
PSK.  

Requires WPA Passphrase.

 

wpa-psk128 

Migration mode w/Cipher suite TKIP+128 bit WEP using WPA 

PSK.  

Requires WPA Passphrase.

 

WPA Passphrase 

(Preshared Key) 

Enter your WPA passphrase. 

Re-enter Passphrase 

Confirms WPA passphrase entry 

Leap User ID 

User ID for Leap security mode 

Leap Password 

Password for Leap security mode 

Re-enter Leap Password 

Confirm password for Leap security mode 

WEP Authentication 

Enables or disables WEP authentication: 

    Automatic 

= automatically detects the authentication. (default) 

    Open System  = communicates the key across the network. 

    Shared Key 

= allows communication only with devices with identical WEP settings. 

Default Key 

Selects the default WEP Key from 1 – 4 if Shared Key or Both is selected for WEP 
Authentication.  
Default is WEP Key 1. 

WEP Key 1 through 4 

Specify up to four WEP key values: 

    If WEP Encryption = 64, enter 10 hexadecimal digits for each key. 

    If WEP Encryption = 128, enter 26 hexadecimal digits for each key. 

Содержание M-Class Mark II M-4206





















Отзывы: