Datalogic QuickScan QD24 series Скачать руководство пользователя

Страница: 240 / 314

Message Formatting

230

QuickScan™ I QD24XX/QBT24XX/QM24XX

LED and Beeper Control

ESC [ 0 q

Emit short High tone + short delay

ESC [ 1 q

Emit short Low tone + short delay

ESC [ 2 q

Emit long Low tone + short delay

ESC [ 3 q

Emit good read tone

ESC [ 4 q

Emit bad tx tone

ESC [ 5 q

Wait 100 ms

ESC [ 6 q

Turn on the green LED

ESC [ 7 q

Turn off the green LED

ESC [ 8 q

Turn on the green spot

ESC [ 9 q

Turn off the green spot

ESC [ 0 r

Beep for Find me function (new)

ESC [ 1 r

Power-off (new)

The LED control escape sequences are intended to activate the LEDs for short periods of time

and can be used in combination with the Beeper. The LED and Beeper will be controlled by the

system after the entire command sequence is interpreted.

Example:

ESC [ 6 q ESC [ 3 q ESC [ 7 q

Turns on the green LED, emits a good read tone, and turns off the
green LED.

ESC [ 6 q ESC [ 5 q ESC [ 7 q

Turns on the green LED for 100 ms and then turns off the green
LED.

Escape sequences different from those listed will be ignored.

Содержание QuickScan QD24 series



























































































































































































































































































































Результаты поиска

Содержание QuickScan QD24 series

Отзывы:

Похожие инструкции для QuickScan QD24 series

Бренды по названию

Популярные бренды

Datalogic QuickScan QD24 series, Руководство по продукции

Результаты поиска

Содержание QuickScan QD24 series

Отзывы:

Похожие инструкции для QuickScan QD24 series

Бренды по названию

Популярные бренды