Datakom DKM-250 Скачать руководство пользователя страница 4

Страница: 4 / 42

DKM-250 User Manual V-2.0

Before installation:

Read the user manual carefully, determine the correct connection diagram.

Remove all connectors and mounting brackets from the unit, then pass the unit through the mounting
opening.

Put mounting brackets and tighten. Do not tighten too much, this can damage the enclosure.

Make electrical connections with plugs removed from sockets, then place plugs to their sockets.

Be sure that adequate cooling is provided.

Be sure that the temperature of the environment will not exceed the maximum operating temperature in any
case.

Be sure that the unit is not subject to water spill.

Below conditions may damage the device:

Incorrect connections.

Incorrect power supply voltage.

Voltage at measuring terminals beyond specified range.

Current at measuring terminals beyond specified range.

Voltage applied to digital inputs over specified range.

Overloading or short-circuiting relay outputs

Connecting or removing data terminals when the unit is powered-up.

High voltage applied to communication ports.

Excessive vibration, direct installation on vibrating parts.

Below conditions may cause abnormal operation:

Power supply voltage below minimum acceptable level.

Current Shunt must be used for current measurement.

No direct connection allowed

1. INSTALLATION INSTRUCTIONS

Содержание DKM-250











































Результаты поиска

Содержание DKM-250

Отзывы:

Похожие инструкции для DKM-250

Бренды по названию

Популярные бренды

Datakom DKM-250, Руководство пользователя

Результаты поиска

Содержание DKM-250

Отзывы:

Похожие инструкции для DKM-250

Бренды по названию

Популярные бренды