Datakom D-700 MK3 Скачать руководство пользователя страница 12

Страница: 12 / 218

D-700 MK3 User Manual Firmware V-16.8

- 12 -

Before installation:

▪

Read the user manual carefully, determine the correct connection diagram.

▪

Remove all connectors and mounting brackets from the unit, then pass the unit through the

mounting opening.

▪

Put mounting brackets and tighten. Do not tighten too much, this can break the enclosure.

▪

Make electrical connections with plugs removed from sockets, then place plugs to their sockets.

▪

Be sure that adequate cooling is provided.

▪

Be sure that the temperature of the environment will not exceed the maximum operating

temperature in any case.

Below conditions may damage the device:

▪

Incorrect connections.

▪

Incorrect power supply voltage.

▪

Voltage at measuring terminals beyond specified range.

▪

Voltage applied to digital inputs over specified range.

▪

Current at measuring terminals beyond specified range.

▪

Overload or short circuit at relay outputs

▪

Connecting or removing data terminals when the unit is powered-up.

▪

High voltage applied to communication ports.

▪

Ground potential differences at non-isolated communication ports.

▪

Excessive vibration, direct installation on vibrating parts.

Below conditions may cause abnormal operation:

▪

Power supply voltage below minimum acceptable level.

▪

Power supply frequency out of specified limits

▪

Phase order of voltage inputs not correct.

▪

Current transformers not matching related phases.

▪

Current transformer polarity incorrect.

▪

Missing grounding.

Current Transformers must be used for current
measurement.

No direct connection allowed.

1. INSTALLATION INSTRUCTIONS

Содержание D-700 MK3



























































































































































































































Результаты поиска

Содержание D-700 MK3

Отзывы:

Похожие инструкции для D-700 MK3

Бренды по названию

Популярные бренды

Datakom D-700 MK3, Руководство пользователя

Результаты поиска

Содержание D-700 MK3

Отзывы:

Похожие инструкции для D-700 MK3

Бренды по названию

Популярные бренды