Datakom D-700 MK3 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 218

background image

D-700 MK3 User Manual Firmware V-16.8

D-700 MK3

ADVANCED

GENSET

CONTROLLER

D-700 MK3 is a next generation genset controller
combining multi-functionality and wide communication
capabilities together with a reliable and low-cost
design.

The same controller provides synchronization, load
share, AMF, DC Genset, ATS, Remote Start, Engine
Control and Remote Display Panel functionalities.

The module comes ready for remote monitoring over
GSM or Ethernet with plug-in communication modules.

Various plug-in modules provide unlimited expansion
capabilities allowing to meet any special requirement.
The unit complies and mostly exceeds world’s tightest
safety, vibration and environmental standards for the
industrial category.

Software features are complete with easy firmware
upgrade process through USB port.

The Windows based PC software allows monitoring
and programming through USB, RS-485, Ethernet and
GPRS. The Rainbow Scada web monitoring service
allows monitoring and control of an unlimited number
of gensets through any web browser.

Multi genset synchronizer and load share *
Multi genset mains synchronizer *
Single genset parallel with mains *
DC genset controller *
AMF unit with uninterrupted transfer
ATS unit with uninterrupted transfer
Remote start controller
Manual start controller
Engine controller
Remote display & control unit *
Waveform display of V & I
Harmonic analysis of V & I

*

Optional with plug-in module

•

Ethernet port (100Mbps) *

• GSM-GPRS *
• Embedded web server *
• Web monitoring *
• Web programming *
• Central Monitoring through internet *
• SMS message sending *
• E-mail sending *
• Central monitoring *
• Modbus RTU through RS-485 *
• Modbus TCP/IP *
• SNMP *
• USB Host *
• CANBUS-2 for inter- module comm. *
• USB Device
• PC software: Rainbow Plus
• J1939-CANBUS for electronic engines

*

Optional with plug-in module

3 phases 4 wires, star
3 phases 4 wires, delta
3 phases 3 wires, delta, 3 CTs
3 phases 3 wires, delta, 2 CTs (L1-L2)
3 phases 3 wires, delta,2 CTs (L1-L3)
2 phases 3 wires, L1-L2
2 phases 3 wires, L1-L3
1 phase 2 wires

FUNCTIONALITIES

COMMUNICATIONS

TOPOLOGIES

DESCRIPTION

1
2
3
...
»

Содержание D-700 MK3



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D-700 MK3

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: IBM Страницы: 105

Бренд: Saitek Страницы: 4

Бренд: Jeep Страницы: 32

Бренд: Accel Страницы: 8

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: Bard Страницы: 102

Бренд: Vestil Страницы: 6

Бренд: END ARMATUREN Страницы: 32

Бренд: Nice Страницы: 40

Network Device NXC-8160s

Бренд: ZyXEL Communications Страницы: 67

Бренд: Gliderol Страницы: 2

Бренд: Hahnel Страницы: 36

Бренд: maxon motor Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды