background image

 

 

DT-IPTV-QAM-ASI-2H |  Manual V1.0 | 01152019 

 

Installation

 

System Installer must adhere to Article 820-40 of the NEC that provides guidelines for proper 

grounding and specifies that the cable ground shall be connected to the grounding system of the 

building, as close to the point of cable entry as possible

 

Unpacking and Inspection 

Each unit is shipped factory tested. Ensure all items are removed from the container prior to discarding 

any packing material. 
Thoroughly inspect the unit for shipping damage with particular attention to connectors and controls. If 

there is any sign of damage to the unit or damaged or loose connectors contact your distributor 

immediately. Do not put the equipment into service if there is any indication of defect or damage.   

Hardware Installations and Connections

 

It is highly recommended that quality cables and connectors be used for all video and audio 

source connections. 

1. 

The unit is designed to be rack mounted in a standard EIA 19” rack. 

2. 

The unit comes standard with HDMI, Component, and Composite video inputs. The encoder / 

modulator are intelligently designed to detect the video input from the video source. 

HDMI 

Connection:

  Connect the HDMI cable(s) from the video source(s) into the HDMI input(s). If 

using a 

Component Video

 

Cable

, connect the Y (Green), Pb (Blue), and Pr (Red) video source 

cable to the unit’s Component input ports. If using a 

Composite Video

 

source, use a 75Ω coaxial 

cable with RCA connectors to connect the 

video source

 (e.g., CATV, DVD, VCR, Camera) to the 

unit’s CVBS port (IN1,IN2).   

    Repeat this step for each video source connection. 

3. 

Component / Composite Audio inputs

: Connect A/V audio input (Left / Right Audio) use RCA 

cables to connect the 

audio source

 to the red / white 

AUDIO L and AUDIO R INPUT jacks 

(IN1,IN2). Repeat this step for each audio source connection.   

    Be sure the video and audio connections for each source are consistent with the unit’s inputs 

(IN1,IN2). 

4. 

Use  a  quality  75Ω  coaxial  cable  with  “F”  connectors  from  the  unit’s 

RF OUT jack

  to the 

distribution system

 (combiner or reverse splitter) or directly to a television. 

5. 

If your device is equipped with an IP output- connect the Ethernet cable to the IP output RJ45 

connector. 

6. 

If your device is equipped with an ASI output- connect the BNC cable to the ASI output. 

7. 

If your device is EAS equipped make the proper connections (contact replay and Video /Audio 

Inputs) to the EAS device. 

8. 

Connect the included power cord to the unit’s 

POWER

 plug. 

9. 

  Connect the power cord to an appropriately rated AC power outlet. 

 

Содержание DT-IPTV-QAM-ASI-2H































Отзывы: