Data Translation DT3145 Скачать руководство пользователя страница 56

Страница: 56 / 60

Chapter 6

E-Mail and Fax Support

You can also get technical support by e-mailing or faxing the
Technical Support Department:

•

E-mail

: You can reach Technical Support at the following

address: [email protected]

Ensure that you provide the following minimum information:

−

Your name,

−

Your company or organization,

−

A phone number,

−

An e-mail address where you can be reached,

−

The hardware/software product you need help on,

−

A summary of the issue you are experiencing,

−

Your contract number, if applicable, and

−

Your product serial number or purchase date.

Omitting any of the above information may delay our ability to
resolve your issue.

•

Fax

: Photocopy and complete the form on

page 47

, then fax

Technical Support at the following number: (508) 481-8620.

World-Wide Web

For the latest tips, software fixes, and other product information, you
can always access our World-Wide Web site at the following address:
http://www.datatranslation.com

Содержание DT3145





























































Результаты поиска

Содержание DT3145

Отзывы:

Похожие инструкции для DT3145

Бренды по названию

Популярные бренды

Data Translation DT3145, Руководство по началу работы

Результаты поиска

Содержание DT3145

Отзывы:

Похожие инструкции для DT3145

Бренды по названию

Популярные бренды