Data-Linc Group FLC910E Скачать руководство пользователя страница 7

Страница: 7 / 28

FLC910E User’s Guide

PN 161-09856-001A

June 2010

Installation

Unpacking the Hardware

•FLC910E OFDM Industrial High-Speed Modem

•120 VAC Wall Transformer (US Power Connector)

•Cat5 Ethernet Cable

•CD with Manual

•Quick Start Guide

•Test Antenna

The equipment was carefully packaged to prevent shipping damage. It should be free from any defect, electrical or me

chanical, and in good operating condition. If your package contents are damaged or missing, please contact your place

of purchase immediately.

Hardware Overview

Front Panel

•Power 3 pin Pluggable Terminal Block.

Left to Right (Frame Ground, Power Ground, Power Positive)

•RJ45 Ethernet Connector.

•Reset Button.

Side Panel

•Antenna Connector with Standard Thread SMA Connector.

Top Panel

-LED Indicators:

LED

Indication

Note

Power

Modem Power

Should be on (green) at all times

Status

Loading or Changing

Start-Up

On = Entering Boot Mode

Off = While Finishing Boot Mode

Operating

Slow Blinking = Reset Button Held for ~ 3 Seconds

Fast Blinking = Reset Button Held for > 3 Seconds

Note:

The Status LED will blink while a firmware up

grade of reset to factory default occurs and the unit will

reboot automatically

RSSI (5 Levels) Signal Strength

Shows signal strength for

Station Adaptors

and

Wireless

Interbuilding Mode

RF Links

Lan Act

Lan Connection

On = 100BaseT Connection

Off = 10BaseT Connection

Blinking = Lan Activity

Lan (100)

100BaseT Connection

On = 100BaseT Connection

Off = 10BaseT if Lan Act is ON

W-Lan

Wireless Link Status

On = Wireless Connected (But no Activity)

Off = No Wireless Link

Blinking = Wireless Activity (Either Data or Linking)

Содержание FLC910E





























Результаты поиска

Содержание FLC910E

Отзывы:

Похожие инструкции для FLC910E

Бренды по названию

Популярные бренды

Data-Linc Group FLC910E, Руководство пользователя

Результаты поиска

Содержание FLC910E

Отзывы:

Похожие инструкции для FLC910E

Бренды по названию

Популярные бренды