Data-Linc Group FLC910E Скачать руководство пользователя страница 18

Страница: 18 / 28

PN 161-09856-001A

June 2010

FLC910E User’s Guide

Appendix B: Radio Setting Details

After successfully logging in the About page is the displayed page. This gives you the

current device name, MAC Address, and the firmware version.

Located on the left margin of the page is the list of setting to change for configuration.

A brief list of the fields in each section is as follows:

Basic Setup:

(Described in detail in Part A)

Device Name, Ethernet Data Rate, Spanning Tree Protocol, VLAN(802.1Q),

Management VLAN ID, IP Address options, and Time server options.

Radio: (Radio Settings)

(Described in detail in Part B)

Operating Mode, Modulation, Channel/ Frequency, Data Rate, Output Power,

Bandwidth, VQoS / TDM, Regatta Mode, and Advanced Parameters.

VBS/VLAN Settings:

(Described in detail in Part C)

The Security Profiles for Base Station, Station Adapter , WDS and Wireless

Interbuilding mode and VLAN (802.1Q) Setup.

Access Control:

(Described in detail in Part D)

To add and remove access control based on MAC Addresses.

WDS Control:

(Peer-to-Peer Links) (Described in detail in Part E)

Setup wireless point to point or multipoint WDS systems based on MAC

Addresses or automatic repeating.

Connections:

(Described in detail in Part F)

Shows the units connected to the device or connection status of the

Station adaptor.

Statistics:

(Described in detail in Part G)

Shows the Ethernet and Wireless statistics for a selected connection group.

Change Password:

(Described in detail in Part H)

Changes the password with the known current password.

Remote Management:

(Described in detail in Part I)

Remote Console (SSH) and SNMP options.

Upgrade Firmware:

(Described in detail in Part J)

Load a new firmware file.

Backup/Restore Settings:

(Described in detail in Part K)

Save or load store configurations.

Event Log:

(Described in detail in Part L)

SysLog setup and Event Log.

Reboot:

(Described in detail in Part M)

Reboots the FLC910E.

Содержание FLC910E





























Результаты поиска

Содержание FLC910E

Отзывы:

Похожие инструкции для FLC910E

Бренды по названию

Популярные бренды

Data-Linc Group FLC910E, Руководство пользователя

Результаты поиска

Содержание FLC910E

Отзывы:

Похожие инструкции для FLC910E

Бренды по названию

Популярные бренды