Data Industrial 330 Скачать руководство пользователя

Страница: 4 / 9

Data Industrial

Model 330 Owner’s

Manual

DIC Comm Port

DIC Comm.

Port

utput

N.C.

ComB

GND

Low

Location of the

DIC Communication Port

Communications cable wiring

Field calibration requires a Data Industrial A330 Programming kit

(consisting of a custom cable and software) and a PC running

Windows

9x, ME, NT, 2000 or XP. In order to program, the Model

330 must be connected to power, and the A301 cable must be

connected to the Model 330 Comm port connector and an available

9-pin COM port on a computer.

Note:

The Data Industrial A301 Cable will work with all 300 Series

products. However the older version of the cable (A300) does

not have sufficient bandwidth to work with the 340 Series Transmitters.

Data Industrial provides free programming software updates via the Internet for all of 300

Series devices. Go to www.dataindustrial.com for these updates.

Содержание 330










Результаты поиска

Содержание 330

Отзывы:

Похожие инструкции для 330

Бренды по названию

Популярные бренды

Data Industrial 330, Руководство пользователя

Результаты поиска

Содержание 330

Отзывы:

Похожие инструкции для 330

Бренды по названию

Популярные бренды