background image

Data Industrial 

Model 330 Owner’s 

Manual

2

Wall Mounting

Optional metal and plastic enclosures are available

to mount the Model 330 to a wall when no other

enclosure is used. The enclosure is first attached

to the wall using fasteners through its mounting

holes.

After wiring, the transmitter may be attached to the

enclosure with the terminal headers facing in using

the slots in the mounting flanges.  As an alternate

mounting arrangement, the Model 330 may be

fastened to the box cover using double-sided

adhesive tape.

Electrical Installation

All connections to the Model 330 are made to screw

terminals on removable headers.

Power Supply Wiring

The Model 330 requires 12-24 Volts AC or DC to

operate. The power connections are made to the

ORANGE header.  The connections are labeled beside

the header.  Observe the polarity shown on the label.

If a Data Industrial plug in type power supply

(A-1026 or A-503) is used connect the black/white

striped wire to the terminal marked positive (+) and the

black wire to the terminal marked negative (-).

Note:

Included with every Model 330 is a 330IK kit

containing a screw, lock washer and ground lead to

connect the Model 330 to Earth Ground.  This will

help prevent electrical interference from affecting the Model 330’s normal operation.

330 Optional Enclosure Dimensions

Side

4.5”

2.8”

2.0”

TOP

SIDE

Sample Power Supply Wiring Diagram

Power Out

AC Load/DC +

AC Common/DC -

DC  +

or

AC Load

DC  -

or

AC  Com m on

E arth
G round

AC or DC

Power Supply

Side View - Typical 300 Series
Removable Connector Wiring

3/32” Flathead 
Screwdriver

Series 300
Connector

Wire

Model 330 Dimensions

1.50”

3.65”

3.25”

.875”

1.75”

Side

1.50”

2.75”

®

Industrial

Power
(+)

(-)

Shield

AC Load/DC +

AC Common/DC -

DIC Comm.

Port

Output

Input

®

Model: 330
SN# 0000000

NO1
NO2
NC1
NC2

Hi

Com

Lo

Содержание 330










Отзывы: