Data General AViiON 5500 Series Скачать руководство пользователя | Manualshive

Страница: 24 / 192

background image

About AViiON 5500 and 550 series computers

1-4

014–002250–01

Internal mass-storage drives

The internal SCSI-2 bus supports up to five of the following
mass-storage drives housed internally:

D

One 5.25-inch removable-media device:

320/525-Mbyte quarter-inch cartridge (QIC) SCSI tape drive

600-Mbyte CD-ROM drive

D

One to four 3.5-inch devices (maximum of one removable-media
drive):

1.44-Mbyte diskette drive

4mm digital audio tape (DAT)

2-Gbyte (half-height)

1-Gbyte (half-height)

520-Mbyte (half-height)

Mounting hardware and cabling for up to five internal drives are
part of each computer unit.

A factory-installed label on the computer rear panel identifies the
position and SCSI ID of your internal drives.

External mass-storage options

The SCSI bus connector(s) on the computer unit rear panel allow
you to connect external SCSI-based mass-storage devices to your
computer system. Each SCSI bus in your system can support as
many as seven SCSI drives.

Refer to Chapter 3 for information about connecting mass-storage
devices using the external SCSI bus connectors on the computer
unit rear panel. Refer to Chapter 5 for information about adding or
replacing drives using the internal SCSI bus connectors and bays.

Refer to the manual that came with the drive and to the manual
that came with the mass-storage housing unit for information about
adding a drive. These manuals also contain specific information
such as environmental specifications, and operating and
maintaining procedures.

«
...
22
23
24
25
26
...
»

Содержание AViiON 5500 Series

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AViiON 5500 Series

Color Computer 3 Basic

Бренд: Tandy Страницы: 17

TRS-80 Model II

Бренд: Tandy Страницы: 36

Бренд: Tandy Страницы: 337

Бренд: Tandy Страницы: 251

Бренд: Chen Hsong Страницы: 124

Бренд: Hatteland Страницы: 44

POWERMATE P - SERVICE 1996

Бренд: NEC Страницы: 178

Бренд: MSI Страницы: 53

Бренд: Black & Decker Страницы: 20

Бренд: NovaSail Страницы: 32

Бренд: BBB Страницы: 3

Бренд: Fanvil Страницы: 50

Бренд: Fanvil Страницы: 57

Бренд: Octagon Страницы: 25

METALLICGEAR NEO-6

Бренд: Phanteks Страницы: 4

Бренд: IEI Technology Страницы: 99

Бренд: Ergotron Страницы: 23

Бренд: Avermedia Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды