Data General AViiON 5500 Series Скачать руководство пользователя | Manualshive

Страница: 22 / 192

background image

About AViiON 5500 and 550 series computers

1-2

014–002250–01

Refer to the following sections of this chapter for an overview of
base (standard) and optional system components; refer to
Appendix A, “Technical specifications,” for more detailed
information.

Base system components

All AViiON 5500 and 550 series computer units include the
following:

D

System board assembly, with:

One 40-megahertz Motorola 88110 microprocessor, plus an
expansion slot for one optional expansion CPU.

One Motorola 88410 Cache/Memory Management Unit (CMMU)
controller with 256-Kbytes cache.

One integrated SCSI–2 narrow (10-Mbits/second) interface
controller.

One integrated IEEE 802.3 Ethernet local area network (LAN)
interface, compatible with thin or thick Ethernet networks
(transceiver not included).

Three asynchronous RS-232-C communications ports.

One integrated RS-232-C port for synchronous communications.

One integrated parallel printer port.

D

Slots for 4 to 12 ECC (error check/correct) SIMMs (single
in–line memory modules) in 32-Mbyte minimum to 256-Mbytes
maximum configurations. Base systems include 32-, 64-, or
128-Mbytes.

D

326-watt power subsystem

D

Two I/O expansion bus slots for optional SCSI or LAN
expansion boards.

D

VMEbus standard backplane printed-circuit board.

AViiON 5500 series systems include a modem for the AV/Alert

SM

service. They require an asynchronous terminal and keyboard to
serve as a system console.

AViiON 550 workstations include a 17- or 19-inch color graphics
monitor, mouse, keyboard, and an 8-bit or 24-bit high-performance
graphics subsystem board.

«
...
20
21
22
23
24
...
»

Содержание AViiON 5500 Series

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AViiON 5500 Series

Бренд: Production Basics Страницы: 3

Бренд: Gateway Страницы: 182

Бренд: M5Stack Страницы: 15

Бренд: Matrox Страницы: 174

Бренд: MSI Страницы: 85

Бренд: Acorn Страницы: 114

Бренд: Acer Страницы: 25

Бренд: Acer Страницы: 70

Бренд: Acer Страницы: 96

Бренд: Acer Страницы: 88

Бренд: Acer Страницы: 134

Бренд: Acer Страницы: 1

Бренд: Acer Страницы: 12

Бренд: Acer Страницы: 38

Бренд: Acer Страницы: 83

Бренд: Acer Страницы: 109

Бренд: Acer Страницы: 116

Бренд: Asus Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды