DAS Smart DL-250 Скачать руководство пользователя страница 17

Страница: 17 / 18

though it resides in AREA #1. The codepad LED's and LCD messages would
now pertain only to AREA #1. NOTE: You can exit the "CHECK" mode by
pressing

[C] [A]

. At this time, the codepad sounder and LED's will refer to Area

#2 only.

Pressing the

[B]

button will advance the codepad to the next authorized Area

which in this case would be AREA #2, and display the message below .

AREA 2 OFF A=ON
C=CHECK B=NEXT

Since AREA #2 shows to be OFF (Disarmed) pressing the

[A]

button will Arm this

area and the screen will display the message below.

AREA 2

ARMED

The message below indicates a FIRE alarm has occurred in Area 1. Enter the
CHECK mode for AREA #1 and press the

[A]

button to find out which zone

created this condition. Then, press the

[#]

button to reset the FIRE zone that has

faulted. NOTE: It takes approximately 15 seconds to reset this condition.

FIRE

AREA 1

The message below indicates a TROUBLE condition with the FIRE zone(s) in
AREA #2. Enter the CHECK mode for AREA #2 and press the

[A]

button to find

out which zone created this condition. Then, press the

[#]

button to reset the FIRE

TROUBLE condition. If this condition does not reset after approximately 15
seconds, call your security installation company and report this condition
immediately.

FIRE TROUBLE

AREA 1

NOTES

Содержание Smart DL-250



















Результаты поиска

Содержание Smart DL-250

Отзывы:

Бренды по названию

Популярные бренды

DAS Smart DL-250, Руководство оператора

Результаты поиска

Содержание Smart DL-250

Отзывы:

Бренды по названию

Популярные бренды