Dantherm CC 3000 Скачать руководство пользователя страница 4

4

Introduction

: About this manual

About this manual

This document is a technical user manual for the CC 3000 free cooling controller intended for 

trained personnel only.

 This manual uses the following abbreviations for ventilation terminologies.

Abb .

Description

GUI/ UI

Graphical User Interface / User Interface

NO/NC

Normally opened (NO) 
• 

a contact that does not flow current in its normal state. Switching it on will 

close the contact, causing it to allow current flow.

Normally closed (NC)
• 

a contact that does flow current in its normal state. Switching it on will open 

the contact and disconnect the flow.

NOC

Network Operation Center

SELV

Safety Extra Low Voltage

SNMP

Simple Network Management Protocol is an internet standard protocol for col-

lecting and organizing information about devices on IP networks and for modify-

ing that information to change device behaviour.

TCP/IP

Transmission Control Protocol/ Internet Protocol

TTL link Hardware interface based on the electrical properties of TTL (Transistor-Transistor 

Logic)

Following symbols are used in this manual in order to draw attention to danger risks and ad-

ditional information of high relevance.

Symbols used

Warning

Caution

WARNING

This symbol in connection with the word “Warning” warns of a risk 

involving severe injury.

Warning

Caution

CAUTION

This symbol in connection with the word “Caution” warns of a risk of 

minor or moderate injury and material damage.

!

NOTICE

In connection with this symbol you will find further tips and information 

concerning the use of the device.

Warning and caution symbols are described in the following way:

Type and source of hazard

 Further elaboration, if relevant.

•  Measures to avert danger or immediate measures if the risk occurs are described in this 

way

Copying of this service manual, or part of it, is forbidden without prior written permission 

from Dantherm.

Dantherm reserves the right to make changes and improvements to the product and the 

service manual at any time without prior notice or obligation.

This unit is designed for long term durability. When total lifetime ends, the unit should be 

recycled according to national rules and with high environmental protection considerations.

Target group

Abbreviations in 

this manual

Symbols in 
this manual

Warning

Caution

WARNING/

CAUTION

Copyright

Reservations

Recycling

Содержание CC 3000









































Отзывы: