DT-50 and DT-50A Tire Changer
7
P/N 5900260 — Rev. A1 — Dec. 2020
Tire Changer components include:
•
Turntable
. Holds and rotates the Wheel and has the Wheel Clamps built in to it.
•
Wheel Clamps
. Holds the Wheel in place, a part of the turntable.
•
Tower
. Supports the Swing Arm, and the Assist Tower.
•
Swing Arm
. Holds the Mount/Demount Head. Moves to the right up to 90
°
when not required.
Comes uninstalled.
•
Assist Tower
. DT-50A only. Holds additional tools that can be used during mounting and
demounting. Comes uninstalled.
•
Mount/Demount Head
. Mounts and demounts Tires. Located on the bottom of the Shaft. The
Tire Changer comes with an alloy steel Head. An optional plastic, non-marring Head is available.
•
Shaft
. Moves up and down; controls the position of the Mount/Demount Head.
•
Shaft Cap
. Moves the Shaft
down
to get the Mount/Demount Head to the desired height.
•
Shaft Lock Handle
. Locks the Swing Arm in the desired position.
•
Swing Control
. Stops the Swing Arm from moving past a specific point you choose.
•
Bead Breaker
. Breaks the Beads of Tires so you can demount them. Located on the right side
of the Tire Changer. Includes a Handle, a Blade, and a movable mechanism.
•
Bead Lifting Tool
. A hand tool used to pull the Bead edge of a Tire over the Mount/Demount
Head so the Tire can be demounted from the Wheel. Can also be used to hold down a Tire
Sidewall during Tire mounting.
•
Turbo-Blast™ Bead Seater
. Directs a burst of air pressure to help seat a difficult Bead. Never
point the Turbo-Blast Nozzle at people or things; use it with caution. Use it only to seat a difficult
Bead, nothing else. Has a Shut-off Valve near the base of the Turbo Blast Hose.
•
Turbo-Blast™ Shut-Off Valve
. Controls when the Turbo-Blast is On/Off. The Shut-Off Valve
must
be turned off when the Turbo-Blast is not in use.
•
Inflation Chuck with Inflation Gauge
. Adds air to a Tire. The Inflation Gauge shows the
amount of air pressure currently in a Tire. Includes an Air Chuck with self-gripping clip and a
release valve button.
•
Inflation Foot Pedal
. Controls air flow to the Inflation Chuck and the Inflation Gauge.
Not
Shown.
•
Lube Bucket
. Holds Tire lubricant. Use a lubricant approved by the Tire manufacturer for the Tire
being changed.
•
Lube Brush
. Applies the Tire lubricant.
•
Bead Breaker Foot Pedal
. Moves the Bead Breaker Blade in.
•
Clamps In/Out Foot Pedal
. Moves all four Wheel Clamps in or out.
•
Turntable Foot Pedal
. Rotates the Turntable. Press down and hold down to rotate the
Turntable clockwise, press up and hold up to rotate the Turntable counter-clockwise.
•
Regulator/Filter
. Controls the pressure of the incoming air supply and removes water from the
incoming air.
•
Lubricator
. Adds lubrication to the incoming air for tools on the Tire Changer that require it.
•
Voltage Switch
.
Not shown.
Switches the Tire Changer’s motor between 110 VAC and 220
VAC operation. Use with
caution
for detailed information). The
Tire Changer comes from the factory set to 110 VAC and the Power Cord has a 110 VAC Plug.
Содержание DT-50
