D2-10 Series Two-Post Lifts
34
P/N 5900249 — Rev. B — February 2021
Installing the Overhead Assembly
The Overhead Assembly goes above and between the Powerside and Offside Posts. It holds the
Equalizing Cables, the Hydraulic Hoses, the Microswitch, its wiring, and the Safety Lock Cable.
The Safety Shutoff Bar and the Microswitch (or two Microswitches if you ordered a three-phase Power
Unit) are installed on the underside of the Overhead Assembly.
The Safety Shutoff Bar shuts off power to the Lift if the top of a Vehicle hits it; this trips the
Microswitch, which cuts off power to the Lift, preventing it from going any higher.
The Microswitch
wiring
goes over the Overhead Assembly and down the Powerside Post to the
Power Unit. Wiring the Microswitch is not covered in this section; it is covered in
. Have your Electrician connect the Microswitch wiring to the Power Unit when they
come out to perform the other electrical tasks.
The Overhead Assembly is two pieces that are bolted together. The Overhead Assembly and the
Safety Shutoff Bar come from the factory already assembled. On rare occasions, the two pieces could
come from the factory unassembled.
To install the Overhead Assembly
:
1.
If the Overhead Assembly came unassembled, locate the two Overhead Assembly pieces and the
four M10 x 1.5 x 25 Hex Head Bolts, four M10 x Ø20 Flat Washers, four M10 x Ø18 Split Lock
Washers, and four M10 x 1.5 Nuts needed to connect them.
2.
Put the Overhead Assembly together in the desired configuration.
3.
Remove all four Overhead Assembly Equalizer Sheaves and their Pins and Bolts from the ends of
the Overhead Assembly pieces.
Keep them nearby, you will be
putting them back into place in
the next section of the installation.
4.
Using a lifting device, raise the
Overhead Assembly into position
on top of the Posts. Bolt the
Overhead to the Posts using the
10 mm Hex nuts and Washers.
5.
The Microswitch
must
be
positioned adjacent to the
Powerside Post. See the figure to
the right.
6.
After installing the Overhead
Assembly, tighten the Anchor
Bolts as detailed in steps 8 and 9
of the Post Installation Procedure,
if they were loosened to aid the
installation of the Overhead
Assembly.
Microswitch Bracket
Powerside Post
Содержание D2-10 Series
