manualshive.com logo in svg
background image

Introduction and Overview

2.1 Connections

Danley DSA signal input and output connections are 
accomplished via RCA Phono and Euroblock style connectors. 
A GPIO (General Purpose In/Out) Euroblock connector enables 
some amplifier functions to be controlled, and wireless or RJ45 
socket Ethernet network connection options are also provided.  

Danley DSA amplifiers have no mains power switch and are 
operational as soon as mains power is connected via the IEC 
60320 mains socket.

2.2 Network Features

Danley DSA amplifiers are TCP/IP network connected devices 
that require a wired or wireless network connection to access 
their configuration menus. The configuration menus are 
accessed via the Danley DSA Control web app interface and 
cover Input, Zone, Output and General Settings functions. The 
configuration menus are fully described in 

Section 4

 of this 

manual.

2.3 Dimensions

Danley DSA amplifier dimensions and features are illustrated 

in 

Diagrams 1a and 1b

. The amplifiers are primarily intended 

for installation in an equipment rack but can also be under-desk 
or wall mounted, or used free standing. They are fan-cooled 
and must be installed such that ventilation apertures are not 
obstructed.

2.4 Firmware

This manual describes the features, functions and user 
interface of Danley DSA amplifiers running 

Firmware Version 

1.2.0.

 

It is strongly recommended that the firmware version 
installed in the amplifier in use is checked initially, and 
regularly thereafter. If updated firmware is available, 
the amplifier should be updated as a priority.

The firmware installed in the amplifier can be identified and 
updated  by selecting the 

Device

 option in the Control web 

app 

Settings Menu

. Firmware versions can be checked, and 

firmware downloaded, from the Danley DSA website:

3. Carton Contents

Danley DSA

 amplifiers are shipped in a cardboard carton 

containing the amplifier unit, a mains cable appropriate for the 
sales territory, an accessory pack, and a document pack. The full 
contents is listed below.

• Amplifier unit

 

• Mains power cable

 

• Input connector x 2

 

• GPIO socket connector

 

• Output connector x 1 or 2

 

• Adhesive rubber feet x 4

 

• Document pack

Содержание DSA125X4























Отзывы: