Daniels UR-4E380-00-000 Скачать руководство пользователя страница 9

Страница: 9 / 58

MT-4E VHF & UHF Receiver & Transmitter Instruction Manual

IM08-MT-4E-TXRX-P1162

General Information

CHannEl and Bank SElECtIon

Four channel select lines, CSEL 0 – CSEL 3, from the motherboard are brought into the receiver and

transmitter modules by the 48-pin rear connector, allowing selection of 16 different channels. These

signals are normally pulled low in the receiver and transmitter, but are typically set by jumpers on

the motherboard to select Channel 1 by default. In addition, a bank select input is provided to switch

between Bank A and B, each of which has 16 channels. The Bank select line normally floats high

(+5 V), selecting Bank A, but may be pulled low or high externally to select Bank B.

Channel and Bank Select line Mapping

The table below shows the relationship between the states of the bank and channel select lines. Note

that the channel select lines follow a binary pattern, but that the binary “0” represents Channel 1.

The Bank A/B select line normally floats high (+5 V), selecting Bank A, but may be pulled low or high

externally via the Bank A/B select line.

BANK A/B

CSEL 3

CSEL 2

CSEL 1

CSEL 0

BANK

SELECTED

CHANNEL

SELECTED

Содержание UR-4E380-00-000



























































Результаты поиска

Содержание UR-4E380-00-000

Отзывы:

Похожие инструкции для UR-4E380-00-000

Бренды по названию

Популярные бренды

Daniels UR-4E380-00-000, Инструкция по эксплуатации

Результаты поиска

Содержание UR-4E380-00-000

Отзывы:

Похожие инструкции для UR-4E380-00-000

Бренды по названию

Популярные бренды