Daniels UR-4E380-00-000 Скачать руководство пользователя страница 51

Страница: 51 / 58

MT-4E VHF & UHF Receiver & Transmitter Instruction Manual

IM08-MT-4E-TXRX-P1162

Specification Data Sheets

380–406 MHz tRanSMIttER

PERFoRManCE SPECIFICatIonS

General

Frequency Range:

380–406 MHz

Carrier Frequency Stability:

± 0.5 ppm

Channel Spacing:

12.5, 15, 25 and 30 kHz

Channel Selection:

6.25 kHz

Number of Channels:

Preset capability for 2 banks of 16 channels

Compatibility:

MT-3 and MT-4 Series Radio Systems; P25 interoperable*

RF Output Power:

0.5 to 6.0W Continuous

Emission Designators:

n/a

System Impedance:

50 Ω; Type-N connector

Duty Cycle:

100%; Continuous operation

Undesired Emissions:

(Adjacent Channel Power Ratio)

< -70 dBc, Wide Band Analog

< -60 dBc Narrow Band Analog

< -67 dBc, Digital*

Undesired Emissions:

(Conducted Spurious)

< -70 dBc @ 6.0W RF Output

Intermodulation Attenuation:

≥ 40 dB Analog

≥ 40 dB Digital*

VSWR Protection:

< 20:1 VSWR at all phase angles

Operating Temperature Range:

-30˚C to +60˚C

Operating Humidity:

95% RH (non-condensing) at +25°C

Operating Voltage:

+13.8 VDC Nominal (range +10 to +17 VDC) †

+9.5 VDC Regulated

Transmit Current:

< 1.7A @ 2.0W RF Output

< 2.8A @ 6.0W RF Output

Stand By Current:

<50 mA (no encryption installed)

<80 mA (with encryption modules installed)

Front Panel Controls:

Transmitter Power On (Norm) / Off / Key Tx

Mic Mode: Analog / Digital

Analog and Digital Transmit LED indicators

PTT Time-Out-Timer:

Programmable from 15 to 465 sec. (in increments of 15 sec., ± 5 sec.) or

infinity (default 300 sec.) using Radio Service Software.

Audio Input:

600 Ω balanced or unbalanced input

(600 Ω or 15k Ω selectable input impedance)

Audio Frequency Response:

Pre-emphasis; +1, -3 dB (300 to 3000 Hz)

Audio Deviation Limiting:

± 2.5 kHz Narrow band, ± 5.0 kHz Wide band

Audio Distortion:

< 2% THD; 1 kHz tone at 1.5 kHz or 3 kHz deviation

FM Hum and Noise Ratio:

≥ 40 dB Wide Band Analog (0.3 to 3.4 kHz De-emphasis off)
≥ 34 dB Narrow Band Analog (0.3 to 3.4 kHz De-emphasis off)

CTCSS Decode / Encode:

Programmable to any of 42 CTCSS tones.

* P25 Digital specifications are applicable only for modules with the P25 Digital firmware upgrade.

Содержание UR-4E380-00-000



























































Результаты поиска

Содержание UR-4E380-00-000

Отзывы:

Похожие инструкции для UR-4E380-00-000

Бренды по названию

Популярные бренды

Daniels UR-4E380-00-000, Инструкция по эксплуатации

Результаты поиска

Содержание UR-4E380-00-000

Отзывы:

Похожие инструкции для UR-4E380-00-000

Бренды по названию

Популярные бренды