Daniels UR-4E380-00-000 Скачать руководство пользователя страница 47

Страница: 47 / 58

MT-4E VHF & UHF Receiver & Transmitter Instruction Manual

IM08-MT-4E-TXRX-P1162

Specification Data Sheets

430–450 MHz RECEIvER

PERFoRManCE SPECIFICatIonS

General

Frequency Range:

430–450 MHz

Channel Spacing:

12.5, 15, 25 and 30 kHz

Channel Selection:

6.25 kHz

Number of Channels:

Preset capability for 2 banks of 16 channels

Channel Switching Range:

± 2.0 MHz

Compatibility:

MT-3 and MT-4 Series Radio Systems; P25 interoperable*

System Impedance:

50 Ω (Type-N connector)

Frequency Generation:

Internal Synthesizer

Reference Sensitivity:

≤-116 dBm (0.35uV) for 12 dB SINAD

≤-116 dBm (0.35uV) for 5% BER

Local Oscillator Frequency Stability:

± 0.5 ppm

Adjacent Channel Rejection (Selectivity):

≥ 45 dB; Narrow Band Analog

≥ 75 dB; Wide Band Analog

≥ 60 dB; Digital*

Intermodulation Rejection:

≥ 75 dB; Narrow Band and Wide Band Analog

≥ 80 dB; Digital*

Spurious Response Rejection:

≥ 75 dB; Narrow Band and Wide Band Analog

≥ 90 dB; Digital*

Conducted Spurious Output Power:

≤ -95 dBm

Hum and Noise Ratio:

≥ 34 dB; Narrow Band Analog

≥ 40 dB; Wide Band Analog

Audio Output:

600 Ω balanced line output (configurable for unbalanced line);

De-emphasis or Flat output, +3 dBm maximum level

Audio Distortion:

Analog:

≤

2.0% (25°C);

≤ 3.0% (-30˚C to +60˚C)

Digital as per TIA / EIA 102.CAAB*

Front Panel Controls:

Receiver Power On (Norm) / Off

Squelch Disable (Push button)

Analog and Digital Receive LED indicators

COR Interface:

150 mA, 50V open drain power MOSFET

Supply Voltage:

+13.8 VDC Nominal (range +10 to +17 VDC) †

+9.5 VDC Regulated

Supply Current:

< 270 mA; with no encryption module installed

< 300 mA; with encryption module installed

Operating Temperature Range:

-30°C to +60°C

Operating Humidity:

95% RH (non-condensing) at +25°C

CTCSS Decode:

Programmable to any of 42 CTCSS tones

DCS Decode:

Programmable to any of 83 DCS sequences. Normal or inverted

DCS can be selected.

IC Certification No.:

n/a

FCC ID:

n/a - Declaration of Conformity (DOC)

* P25 Digital specifications are applicable only for modules with the P25 Digital firmware upgrade.

†

For GSA BPA Contract: GSC-TFMG-BPA-09-002 the following specifications apply:

Supply Voltage range: +10 to +18 VDC

Содержание UR-4E380-00-000



























































Результаты поиска

Содержание UR-4E380-00-000

Отзывы:

Похожие инструкции для UR-4E380-00-000

Бренды по названию

Популярные бренды

Daniels UR-4E380-00-000, Инструкция по эксплуатации

Результаты поиска

Содержание UR-4E380-00-000

Отзывы:

Похожие инструкции для UR-4E380-00-000

Бренды по названию

Популярные бренды