background image

Remove end cover, gear set, cardan shaft, distributor plate, O-rings and valves from gear set end of housing

To remove end cover, gear set, cardan shaft, distributor plate, suction-, LS-check- and emergency steer
valves from housing, follow these steps.

End cover, gear set, cardan shaft, distributor plate, O-rings, and valves parts

Wrench size and torque

Item

Description

Wrench size

Torque

31

Screw

13 mm socket spanner

30 ± 6 N•m [265 ± 52 lbf•in]

32

Pin bolt screw

13 mm socket spanner

30 ± 6 N•m [265 ± 52 lbf•in]

4

Threaded bushing

12 mm screw driver

-

172

Pin bolt screw for LS check

2 mm Hex key

1 ± 0.1 N•m [8.9 ± 0.9 lbf•in]

1. Screw off the six screws (31) using a 13mm socket spanner.
2. Screw off the pin bolt screw (32) using a 13mm socket spanner.
3. Remove the washers (35).
4. Remove the end cover (36) by sliding sideward.
5. Lift the gear wheel set (30) off the unit.

Remove the two O-rings (39) from the gear rim.

6. Remove the cardan shaft (13).
7. Remove the distributor plate (34).
8. Remove the O-ring (6) from housing.
9. Screw out the Pin bolt screw (172) using a 2mm Hex key.

10. Drag out the suction pins (80) using a hook.

It may be needed to line up the suction pin in the thread bore with a 2mm screw driver before it will

be possible to insert the hook into the cross hole of the suction pins.

11. Screw out threaded bushing (4) using a 12mm screw driver.

Service Manual

VSPP Steering unit

VSPP disassembly

 

©

 Danfoss | November 2019

AX319758618681en-000101 | 15

Содержание VSPP





































Отзывы: