Danfoss VLT AutomationDrive FC 301 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 92

background image

2 Safety

2.1 Safety Symbols

The following symbols are used in this document:

WARNING

Indicates a potentially hazardous situation which could
result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which could
result in minor or moderate injury. It can also be used to
alert against unsafe practices.

NOTICE!

Indicates important information, including situations that
can result in damage to equipment or property.

2.2 Qualified Personnel

Correct and reliable transport, storage, installation,
operation, and maintenance are required for the trouble-
free and safe operation of the adjustable frequency drive.
Only qualified personnel are allowed to install or operate
this equipment.

Qualified personnel are defined as trained staff, who are
authorized to install, commission, and maintain equipment,
systems, and circuits in accordance with pertinent laws and
regulations. Additionally, the qualified personnel must be
familiar with the instructions and safety measures
described in this instruction manual.

2.3 Safety Precautions

WARNING

HIGH VOLTAGE

Adjustable frequency drives contain high voltage when
connected to AC line power input, DC power supply, or
load sharing. Failure to perform installation, start-up, and
maintenance by qualified personnel can result in death
or serious injury.

•

Installation, start-up, and maintenance must be
performed by qualified personnel only.

WARNING

UNINTENDED START

When the adjustable frequency drive is connected to AC
line power, DC power supply, or load sharing, the motor
may start at any time. Unintended start during
programming, service, or repair work can result in death,
serious injury, or property damage. The motor can start
via an external switch, a serial bus command, an input
reference signal from the LCP, or after a cleared fault
condition.
To prevent unintended motor start:

•

Disconnect the adjustable frequency drive from
line power.

•

Press [Off/Reset] on the LCP before
programming parameters.

•

The adjustable frequency drive, motor, and any
driven equipment must be fully wired and
assembled when the adjustable frequency drive
is connected to AC line power, DC power
supply, or load sharing.

Safety

Instruction Manual

8

Danfoss A/S © Rev. 09/2014 All rights reserved.

MG33AP22

2

2

«
...
8
9
10
11
12
...
»

Содержание VLT AutomationDrive FC 301





























































































Отзывы:

Нет отзывов

Похожие инструкции для VLT AutomationDrive FC 301

Бренд: GFA Страницы: 21

Бренд: Omron Страницы: 9

Бренд: Minarik Страницы: 52

Бренд: Carotron Страницы: 42

Бренд: SSD Drives Страницы: 319

Servo Motor Kit

Бренд: Terasic Страницы: 20

Бренд: ANCA Motion Страницы: 170

Бренд: Sanyo Denki Страницы: 119

Бренд: Micro Solutions Страницы: 29

Бренд: Motion Страницы: 2

iPOS80x0 BX-CAN

Бренд: Technosoft Страницы: 41

iPOS3602 HX-CAN

Бренд: Technosoft Страницы: 41

Бренд: Technosoft Страницы: 54

CIMR-AC4A0103TAA

Бренд: YASKAWA Страницы: 40

Бренд: National Instruments Страницы: 32

Бренд: YASKAWA Страницы: 603

Бренд: Zest Страницы: 29

Бренд: YASKAWA Страницы: 187

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды