Danfoss VLT AutomationDrive FC 300 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 98

Danfoss VLT AutomationDrive FC 300 Скачать руководство пользователя страница 79

ALARM 82, CSIV par. err.
CSIV failed to init a parameter.

ALARM 85, Dang fail PB:
Profibus/Profisafe Error.

WARNING/ALARM 104, Mixing fan fault
The fan monitor checks that the fan is spinning at power-
up or whenever the mixing fan is turned on. If the fan is
not operating, then the fault is annunciated. The mixing-
fan fault can be configured as a warning or an alarm trip
by

14-53 Fan Monitor

.

Troubleshooting Cycle power to the adjustable frequency
drive to determine if the warning/alarm returns.

WARNING 250, New spare part
A component in the adjustable frequency drive has been
replaced. Reset the adjustable frequency drive for normal
operation.

WARNING 251, New type code
The power card or other components have been replaced
and the type code changed. Reset to remove the warning
and resume normal operation.

Warnings and Alarms

VLT

®

Automation Drive D-Frame

Instruction Manual

MG34U222 - VLT

®

is a registered Danfoss trademark

8-11

8

8

«
...
77
78
79
80
81
...
»

Содержание VLT AutomationDrive FC 300



































































































Отзывы:

Нет отзывов