Danfoss VLT 5000 Crane Series Скачать руководство пользователя страница 37

Страница: 37 / 123

VLT® 5000 Crane

■

Control Panel

The VLT 5000 Crane can be combined with an LCP

control unit (Local Control Panel) which makes up a

complete interface for operation and programming

of the frequency converter. The LCP control panel

can be installed up to 3 metres away from the

frequency converter, eg. on a front panel, by

means of the additional mounting kit.

The control panel is divided into five functional groups:

1. Display.

2. Keys used to change the display function.

3. Keys used to change the programme parameters.

4. Indicator lamps.

5. Local control keys.

All data is displayed via a 4-line alphanumeric

display, which during normal operation will be able

to continuously display 4 items of operating data

and 3 operating modes. During programming all

information needed for quick, effective parameter

setup of the frequency converter will be displayed.

As a supplement to the display there are three

indicator lamps for voltage indication (ON), warning

(WARNING) and alarm (ALARM) respectively. All

frequency converter parameter Setups can be changed

immediately from the control panel, after entering

the correct password in parameter 650 and if in

parameter 018

Not Locked

[0] is selected.

✭

= factory setting. () = display text [] = value for use in communication via serial communication port

MG.50.N4.02 - VLT is a registered Danfoss trademark

Содержание VLT 5000 Crane Series




























































































































Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT 5000 Crane Series, Руководство по эксплуатации

Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды