Danfoss VLT 5000 Crane Series Скачать руководство пользователя страница 25

Страница: 25 / 123

VLT® 5000 Crane

■

General Warning before Installation

Before starting the installation, please

be aware of heavy weight and sharp

edges. Furthermore, make sure that

no mains are connected

■

Mechanical Installation

The frequency converter must be installed vertically.

The frequency converter is cooled by means of air

circulation. For the unit to be able to release its cooling

air, the

minimum

distance over and below the unit

must be as shown in the illustration below. To protect

the unit from overheating, it must be ensured that the

ambient temperature

does not rise above the max.

temperature stated for the frequency converter

and

that the 24-hour average temperature

is not exceeded

The max. temperature and 24-hour average can be

seen from the General Technical Data.

■

Enclosure Protection

Compact

VLT 5042 - 5102 400-500 V

IP 20

VLT 5152 - 5202 400-500 V

IP 00

■

Installation of VLT 5042–5062 400-500 V

Compact IP20/IP00
Cooling

All Compact units in the above-mentioned series

require a minimum space of 200 mm above and

below the enclosure and must be installed on a

plane, vertical surface (no spacers).

Side-by-side

Compact IP 00/IP20

All units in the above-mentioned series can be installed

side by side without any space between them, since

these units do not require cooling on the sides.

MG.50.N4.02 - VLT is a registered Danfoss trademark

Содержание VLT 5000 Crane Series




























































































































Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT 5000 Crane Series, Руководство по эксплуатации

Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды