Danfoss VLT 5000 Crane Series Скачать руководство пользователя страница 23

Страница: 23 / 123

VLT® 5000 Crane

■

Fuses

UL compliance

380-500 V

Bussmann

SIBA

Littel fuse

Ferraz-Shawmut

5042

KTS-R100

2028220-125

KLS-R100

A6K-100R

5052

KTS-R125

2028220-125

KLS-R125

A6K-125R

5062

KTS-R150

2028220-160

KLS-R150

A6K-150R

5072

FWH-220

2028220-200

L50S-225

A50-P225

5102

FWH-250

2028220-250

L50S-250

A50-P250

5122

FWH-300

2028220-315

L50S-300

A50-P300

5152

FWH-350

2028220-315

L50S-350

A50-P350

5202

FWH-400

206xx32-400

L50S-400

A50-P400

KTS-fuses from Bussmann may substitute KTN for 240 V drives.

FWH-fuses from Bussmann may substitute FWX for 240 V drives.

KLSR fuses from LITTEL FUSE may substitute KLNR fuses for 240 V drives.

L50S fuses from LITTEL FUSE may substitute L50S fuses for 240 V drives.

A6KR fuses from FERRAZ SHAWMUT may substitute A2KR for 240 V drives.

A50X fuses from FERRAZ SHAWMUT may substitute A25X for 240 V drives.

Non UL compliance

If UL/cUL is not to be complied with, we recommend the above mentioned fuses or:

VLT 5001-5027

200-240 V

type gG

VLT 5001-5062

380-500 V

type gG

VLT 5032-5052

200-240 V

type gR

VLT 5072-5500

380-500 V

type gR

Not following the recommendation may result

in unnecessary damage of the drive in case of

malfunction. Fuses must be designed for protection in

a circuit capable of supplying a maximum of 100000

rms

(symmetrical), 500/600 V maximum.

MG.50.N4.02 - VLT is a registered Danfoss trademark

Содержание VLT 5000 Crane Series




























































































































Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss VLT 5000 Crane Series, Руководство по эксплуатации

Результаты поиска

Содержание VLT 5000 Crane Series

Отзывы:

Бренды по названию

Популярные бренды