Danfoss VLT 2800 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

background image

4.12 EMC-Correct Electrical Installation

General points to observe to ensure EMC-correct electrical
installation.

•

Use only screened/armoured motor cables and
screened/armoured control cables.

•

Connect the screen to ground at both ends.

•

Avoid installation with twisted screen ends
(pigtails), since this ruins the screening effect at
high frequencies. Use cable clamps instead.

•

It is important to ensure good electrical contact
from the installation plate through the installation

screws to the metal cabinet of the frequency
converter.

•

Use starwashers and galvanically conductive
installation plates.

•

Do not use unscreened/unarmoured motor cables
in the installation cabinets.

Illustration 4.9

shows EMC-correct electrical installation, in

which the frequency converter has been fitted in an instal-
lation cabinet and connected to a PLC.

Illustration 4.9 Example of an EMC-correct Electrical Installation

Electrical Installation

Quick Guide

16

Danfoss A/S © Rev. 2014-03-18 All rights reserved.

MG28M202

4

4

«
...
16
17
18
19
20
...
»

Содержание VLT 2800





































Отзывы:

Нет отзывов

Похожие инструкции для VLT 2800

Бренд: Samsung Страницы: 37

Бренд: Samsung Страницы: 2

Бренд: Teac Страницы: 2

Бренд: TDT Страницы: 18

Бренд: Yamaha Страницы: 30

Бренд: Sungrow Страницы: 14

Бренд: Senergy Страницы: 50

Бренд: SAJ Страницы: 59

Бренд: DELTACAST Страницы: 40

Бренд: NAIM Страницы: 22

Media Giant CM3G Series

Бренд: Conceptronic Страницы: 2

Бренд: Lambda Страницы: 47

Бренд: T+A Страницы: 72

Frenic Mini FRN001C1E-2U

Бренд: Fuji Electric Страницы: 196

STEVAL-CTM004V1

Бренд: STMicroelectronics Страницы: 40

Бренд: Datavideo Страницы: 23

Бренд: GPX Страницы: 2

Бренд: Vitus Audio Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды