manualshive.com logo in svg

Danfoss VACON 100 industrial, Руководство по установке, Страница: 49 / 79

Поделиться
Скачать
Danfoss VACON 100 industrial Скачать руководство пользователя страница 49

Fault tracing

vacon • 47

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

6

6.

F

AULT

 

TRACING

When the AC drive control diagnostics detect an unusual operating condition, the drive opens a 
notification, for example, on the keypad. The keypad shows the ordinal number of the fault, the fault 
code and a short fault description.

You can reset the fault with the Reset button on the control keypad or via the I/O terminal. The faults 
are stored in the Fault history menu, which can be browsed. The different fault codes are in the fault 
table below. The fault table presents only the faults related to the fieldbus in use.

If you need support in problems related to PROFINET IO, send a description of the problem together 
with the Drive Info File taken with VACON

®

 Live to your local support. If possible, also send a 

"Wireshark" log from the situation if applicable.

Содержание VACON 100 industrial
















































































Отзывы:

Нет отзывов