Danfoss VACON 100 industrial Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 79

Danfoss VACON 100 industrial Скачать руководство пользователя страница 17

Fieldbus parameterization

vacon • 15

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

4

4.3.1

IP Address mode

The IP mode determines how the drive IP settings are set. If a DHCP server is selected, then the
drive will try to retrieve its IP settings from the DHCP server connected to the local network. If the
drive is unable to retrieve its IP settings, it will set a link-local address as the current IP address
after about one minute (for example 169.x.x.x).

If "Fixed IP" is set as IP mode, the settings from submenu "Fixed IP settings" are used.

In PROFINET network IP settings are usually set by the PLC via DCP protocol during connection
process. When this is happens, IP mode is set to fixed and given settings are stored to "Fixed IP set-
tings".

4.3.2

Active IP address, subnet mask and default gateway

This value cannot be changed. If IP mode is "fixed" then it will display same value as in Fixed IP ad-
dress. If mode is "DHCP", the value is 0.0.0.0 when DHCP is retrieving IP settings or 169.x.x.x if it
could not retrieve an address. Otherwise it shows currently active IP address.

Exception to above is that if IP settings were set from PLC via DCP protocol and PLC set the settings
with flag "temporary", then IP settings are reset during drive startup to "0.0.0.0" and IP mode is still
"Fixed".

4.3.3

MAC address

The MAC address of the control board. MAC address (Media Access Control) is a unique address
given to each network host. It is not editable.

Table 7. Common Ethernet Settings

Panel Tree

Parameter

Range

Default

ID

Description

P5.9.1.1

IP address

mode

Fixed (1),

DHCP(2)

DHCP (2)

2482 IP Mode

P5.9.1.2

Duplicate IP

Detection

Disabled (0),

Enabled (1)

enabled

2569

When disabled drive does not
check for or react to address
conflict situation.

P5.9.1.3.1 IP

address

1.0.0.0 -

223.255.255.255

192.168.0.10

2529 Fixed IP address

P5.9.1.3.2 Subnet

mask

0.0.0.0-

255.255.255.255

255.255.0.0

2530 Fixed Subnet mask

P5.9.1.3.3

Default gate-

way

0.0.0.0-

255.255.255.255

192.168.0.1

2531 Fixed default gateway

P5.9.1.4

Active IP

address

-

-

2483

Shows current active IP
address. It is same as fixed
value if IP mode is "Fixed".

P5.9.1.5

Active subnet

mask

-

-

2484

Shows current active subnet
mask. It is same as fixed value
if IP mode is "Fixed".

P5.9.1.6

Active default

gateway

-

-

2485

Shows current active default
gateway. It is same as fixed
value if IP mode is "Fixed".

P5.9.1.7

MAC address

-

-

2486 Drive MAC address

«
...
15
16
17
18
19
...
»

Содержание VACON 100 industrial
















































































Отзывы:

Нет отзывов