manualshive.com logo in svg

Danfoss PVED-CLS, Руководство для стартапов, Страница: 7 / 48

Поделиться
Скачать
Danfoss PVED-CLS Скачать руководство пользователя страница 7

PVED-CLS hydraulic configuration P3072-P3097

Navigate to the hydraulic configuration section via System Navigator > Configuration > Hydraulic

Config

Example parameter settings

If the parameter change is not described below or conditions are not met, use the default values.

Parameter settings

Parameter

Conditions for value changes

P3072

Not present if there is no cut-off valve (usually with EHPS)

P3078

Set to 0 if PVED-CLS is part of desk setup

P3097

Set to 50 if using 12V coil on a 24V system

P3080

Set to "YES" if using EHPS

P3081

Set to match the valve type used

P3082

If using EHPS, enter desired turns lock-to-lock x100 that matches the hydraulic system

P3084

Set to match OSP displacement in cubic centimeters

P3086

Set to match volume needed to turn lock-to-lock. If using unbalanced cylinder, set to average of left and right.

The default parameters are based on 12V coil. Depending on the voltage, the following parameters may
need to be changed:

Parameter

12V coil

24V coil

P3074

1100mA

550mA

P3076

500mA

250mA

The pre-load parameter P3097 is a PWM signal and it must be set to scale the input voltage down to the
rated current of the spool:

Application Guide

PVED-CLS startup guide

Parameter setting

 

©

 Danfoss | October 2018

AB285975085591en-000101 | 7

Содержание PVED-CLS

















































Отзывы:

Нет отзывов