manualshive.com logo in svg

Danfoss PVED-CLS, Руководство для стартапов, Страница: 27 / 48

Поделиться
Скачать
Danfoss PVED-CLS Скачать руководство пользователя страница 27

PVED-CLS AUX configuration

Navigate to the AUX configuration section via System Navigator > Configuration > AUX Config

The following parameters only apply if AUX is enabled.

Parameter

Conditions for value change

P3646, P3719

See 

PVED-CLS STW configuration

 on page 23

P3647

Set to minimum joystick command in 0.1% needed to switch into joystick steering.

There are seven subsets of AUX configuration that apply only if an AUX device is selected in parameter
P3240 in the Peripherals Config page: 

AUX Mini-wheel programs

, 

Soft-stop

, 

Anti-jerk

, 

Anti-drift

, 

Flow

limitation

, 

Closed loop joystick

, and 

Open loop joystick

.

Approve the parameters by following the steps in 

PVED-CLS parameter acceptance

 on page 8.

PVED-CLS AUX mini-wheel programs
There are 5 AUX programs for mini steering wheels that each have a similar set of parameters. These are

only used if a mini steering wheel is present.

Parameter

Conditions for value change

P3650-P3657

See 

PVED-CLS Steering wheel programs

 on page 23 for configuration details.

Application Guide

PVED-CLS startup guide

Parameter setting

 

©

 Danfoss | October 2018

AB285975085591en-000101 | 27

Содержание PVED-CLS

















































Отзывы:

Нет отзывов