Danfoss MLM116 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 60

background image

Electrical data, connections and wiring

MLZ/MLZ116 compressors are available only in code 4.

Motor voltage

The compressor terminal box according to IEC529 is IP54 for all models when correctly sized IP54 rated
cable glands are used.

First numeral, level of protection against contact and foreign objects

5

- Dust protected

Second numeral, level of protection against water

4

- Protection against water splashing

The temperature inside the terminal box may not
exceed 70°C. Consequently, if the compressor
is installed in an enclosure, precautions must
be taken to avoid the temperature around the
compressor and in the terminal box from rising
too much. The installation of ventilation on the
enclosure panels may be necessary. If not, the

electronic protection module may not operate
properly. Any compressor damage related to this
will not be covered by the Danfoss warranty. In
the same manner, cables must be selected in a
way to ensure that terminal box temperature
does not exceed 70°C.

IP rating

Terminal box

temperature

Electrical power is connected to the compressor
terminals by Ø 4.8 mm (3/16”) screws.

The maximum tightening torque is 3 Nm. Use a
1/4’’ ring terminal on the power leads.

Wiring connections

Motor voltage

code 4

Nominal voltage

50 Hz

380-415 - 3ph

Voltage range

50 Hz

340-457 V

The terminal box is provided with 2 triple
knockouts and 1 single knockout for power
supply and 4 double knockouts for the safety
control circuit.

The 3 power supply knockouts accommodate the
following diameters:
• Ø 50.8 mm (UL 1"1/2 conduit) and Ø 43.7

mm (UL 1"1/4 conduit) and Ø 34.5 mm (UL 1"
conduit)

• Ø 40.5 mm (ISO40) and Ø 32.2 mm (ISO32) and

Ø 25.5 mm (ISO25)

• Ø 25.5 mm (ISO25)

The 4 others knockouts are as follows:
• Ø 22.5 mm (PG16) (UL 1/2") and Ø 16.5 mm

(ISO16) (x2)

• 20.7 mm (ISO20 or PG13.5) (x2)

MLM/MLZ116

Black

Blue

Brown

Faston 1/4" tabs

Power supply

Sump heater

Module

power supply

M1-M2

control circuit

The motor protection module comes preinstalled
within the terminal box. Phase sequence
protection connections and thermistor
connections are pre-wired. The module must be
connected to a power supply of the appropriate
voltage. The module terminals are 6.3 mm size
Faston type.

L N S1 S2 M1 M2

L1 L2 L3

Black Blue Brown

Phase sequence input

Internal control contact

Safety

circuit

Thermistor

connection

Module power

L N

M1 M2

Note: please make sure M1/M2 is connected to OEM controller

and L/N is connected to outside power supply, otherwise, there

will be no motor protection.

12

FRCC.PC.035.A5.02

Application Guidelines

Single compressors

«
...
10
11
12
13
14
...
»

Содержание MLM116





























































Отзывы:

Нет отзывов

Похожие инструкции для MLM116

Craftsman 919.721560

Бренд: Sears Страницы: 20

Бренд: Rietschle Thomas Страницы: 49

Бренд: MasterCraft Страницы: 13

Бренд: Campbell Hausfeld Страницы: 10

SABROE SAB 120 E

Бренд: Johnson Controls Страницы: 62

Бренд: California Air Tools Страницы: 17

Бренд: Carrier Страницы: 20

Advandced F2G2PAK

Бренд: Fini Страницы: 28

Бренд: Faller Страницы: 12

Бренд: Sparmax Страницы: 28

Бренд: ABAC Страницы: 91

Бренд: Danfoss Страницы: 40

Бренд: Global Machine Company Страницы: 16

Бренд: Atlas Copco Страницы: 29

Бренд: Atlas Copco Страницы: 30

Бренд: ULTIMATE SPEED Страницы: 30

Бренд: Eastwood Страницы: 12

Бренд: HARDELL Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды