manualshive.com logo in svg

Danfoss MCB 152, Руководство по установке

Поделиться
Скачать
Danfoss MCB 152 Скачать руководство пользователя страница 33

•

The drive must be wired properly. Refer to 

4.4.3 Wiring Procedures

.

•

All safety equipment such as protective monitoring devices, light barriers, or emergency stop switches are connected and ready for
operation.

•

All motor parameters and command parameters are set correctly in the drive.

Procedure

1. Use the VLT® Motion Control Tool MCT 10 software to generate the commissioning test report.
2. Follow the test sequence in the report to ensure proper functioning of the safety option.
3. Document each individual step of the test.
4. Note the checksum of the safety option parameters in the records.
5. Do not release the system unless it has successfully passed all individual steps of the test.
6. Restart the drive and check that the motor runs normally.

5.6 Operation

WARNING

UNINTENDED BEHAVIOR
Numerous stored data or settings control the behavior of the drive system. Unsuitable settings or data may trigger unexpected
movements or responses to signals and disable monitoring functions. Follow the instructions below to avoid risk of death,
serious injury, or equipment damage.

-

Do NOT operate the drive system with unknown settings or data.

-

Verify that the stored data and settings are correct.

-

When commissioning, carefully run tests for all operating states and potential error situations.

-

Verify the functions after replacing the product and also after changing the settings or data.

-

Only start the system if there are no persons or obstructions in the hazardous area.

Prerequisites for normal operation are:
•

Commissioning is complete.

•

The safety option contains the configuration data.

•

The safety sub-functions have been tested.

•

LED1, LED2, and LED4 are lit.

During operation:
•

Any pulse edge change at the safety option safe input is monitored.

•

The safety sub-functions are performed in accordance with the configuration.

Commissioning

Installation Guide  | VLT®Safety Option MCB 152

AN327351953089en-000101 / 130R0578| 33

Danfoss A/S © 2020.02

Содержание MCB 152



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды