Danfoss iSave 21 Скачать руководство пользователя страница 7

Страница: 7 / 18

Service guide

Disassembling and assembling iSave 21

180R9219 | 521B1171 | DKCFN.PI.003.K4.02 | 03.2016

Assembling the

pressure exchanger

Lubricate all the O-rings and back up

rings with clean filtered water and gently

by help of the 3 compression tools in

every fourth hole mount both valve plate

on the cylinder barrel.

Adjust the distance between the cylinder

barrel and valve plate at the short

shaft end. Distance 4-6 mm.

Lubricate all the bores in the cylinder

barrel with clean filtered water.

Mount the new back-up rings on the

valve plate first and then the new O-rings.

IMPORTANT:
It is essential that the iSave is serviced in
conditions of absolute cleanliness.
All Parts must be absolute clean before

mounting.

WARNING:
Do not use silicone when assembling the
iSave. Do not reuse dismantled O-rings: they
might be damaged. Always use new O-rings.

Lubrication
- To prevent seizing-up, lubricate threads on
screws.
- O-rings inside iSave may be lubricated only
with clean filtered water.

- O-rings for port flange, mounting flange may
be lubricated with a small amount of grease.
- It is important to lubricate ALL parts to be
assembled with clean filtered water (Especially
all PEEK parts).

Содержание iSave 21



















Результаты поиска

Содержание iSave 21

Отзывы:

Бренды по названию

Популярные бренды

Danfoss iSave 21, Руководство по обслуживанию

Результаты поиска

Содержание iSave 21

Отзывы:

Бренды по названию

Популярные бренды