manualshive.com logo in svg

Danfoss iSave 21, Руководство по обслуживанию

Поделиться
Скачать
Danfoss iSave 21 Скачать руководство пользователя страница 11

Service guide 

Disassembling and assembling iSave 21

11

180R9219  |  521B1171  |  DKCFN.PI.003.K4.02  |  03.2016

22.  Shaft seal 

NOT

 mounted correct. 

The rubber seal face must turn into the flange.

23.  Using the plastic assembly tool provided,   

 

large diameter first

, press the seal home  

 

against the shoulder, by hand.

Be careful not to damage the carbon seal face 
on the shaft seal.

24.  Shaft seal in right position:

25.  Remove the old ceramic ring from the  

 

 flange. 

Position the new O-ring on the seal    

 flange.

26.  Push the new ceramic ring into the flange    
 

using plastic tool provided (small diameter).   

 

Make sure the face with the rubber seal is    

 

positioned against the shoulder in the 

 flange. 

Before assembly wet the parts with clean 
filtered water.

27.  Position the seal flange and the bolts.  

 

 

Tighten the 4 bolts with 12 Nm ±1.2 Nm.

Содержание iSave 21



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды