Danfoss erc 112 Скачать руководство пользователя страница 17

"

SdF

"

Min. no
Max. yes
Default yes

Show Defrost

If set to "

yES

", this parameter causes the display to show DEF when the

system is in defrost mode. If set to "

nO

", the temperature continues to 

be displayed.

"

SCS

"

Min. no
Max. yes
Default yes

Show compressor symbol

"

no

": compressor symbol will not show on display.

"

yES

": show compressor symbol on display.

"

SFS

"

Min. no
Max. yes
Default yes

Show Fan symbol

"

no

": san symbol will not show on display.

"

yES

": show fan symbol on display.

"

SdS

"

Min. no
Max. yes
Default yes

Show Defrost symbol

"

no

": defrost symbol will not show on display.

"

yES

": show defrost symbol on display.

"

SES

"

Min. no
Max. yes
Default yes

Show ECO symbol

"

no

": ECO symbol will not show on display.

"

yES

": show ECO symbol on display.

"

Ld

"

Min. -100.0°C
Max. 200.0°C
Default -100

Minimum Display value 

If the probe value is less than minimum display value mentioned in this para-
meter, it doesn't show the actual value and instead show this minimum only 
until the probe starts reading a higher value than minimum display value set 
here.

"

Hd

"

Min. -100.0°C
Max. 200.0°C
Default  200

Maximum display value 

• Controller will display actual temperature, if the probe value is between 

Maximum display value and Signaling threshold value and the trend of the 
probe is increasing (trend is based on past 10 readings)

• Controller will display Error “Err”, if the probe value is more than Signaling 

threshold value and the trend of the probe is increasing (based on the past 
10 readings)

• Controller will display “---“if the probe value is more than signaling thres-

hold and trend of the probe is decreasing (based on the past 10 readings)

• Controller will display “---“if the probe value is bigger than Max display va-

lue and the trend of the probe is decreasing (based on the past 10 readings)

"

St

"

Min. -100.0°C
Max. 200.0°C
Default 200

Signalling threshold value 

Temperature limit for Maximum display visualization

ALA

Alarm settings

"

HAt

"

Min. -100.0°C
Max. 200°C
Default 15.0°C

High Temp Alarm

Absolute value.
By setting "

HAt

" to the maximum alarms will be deactivated.

"

LAt

"

Min. -100.0°C
Max. 200°C
Default -50.0°C

Low Temp Alarm

Absolute value.
By setting "

LAt

" to the minimum value, alarms will be deactivated.

In most situations, the low alarm delay will be set to 0 to warn about
too low a temperature immediately.

"

Htd

"

Min. 0 min
Max. 240 min
Default 30 min

Alarm delay on high temperature alarm

The number of minutes to wait before sounding an alarm once the 
high temperature alarm temperature is reached.

"

Ltd

"

Min. 0 min
Max. 240 min
Default 0 min

Alarm delay on low temperature alarm

The number of minutes to wait before sounding an alarm once the
low temperature alarm temperature is reached.

User Guide | ERC 112 Refrigeration Controller

© Danfoss | DCS (vt) | 2019.07

BC200686422115en-000802 | 17

Содержание erc 112

































Отзывы: