Danfoss EM-PMI540-T4000 страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 71

background image

It is in some cases possible to make an exception from the limitations of the mounting

positions. Document Allowed bearing loads for EM-PMI machines DOC-000454 gives more

information about this. Contact Danfoss to obtain the document.

The electric machine must be installed horizontally. The standard horizontal mounting option (MDH) is
the only possible mounting option. When mounting, the electric machine can be turned around its axis
(shaft) for maximum of 45° both directions from its default installation direction. Along the axis, the tilt
angle may be maximum of 10° both directions. See Figure below.

Nominal allowed horizontal mounting position of the electric machine

Allowed deviations from the horizontal mounting limitations

User Guide

EM-PMI540-T4000

Installation

©

Danfoss | April 2023

BC265857716810en-000202 | 31

«
...
29
30
31
32
33
...
»

Содержание EM-PMI540-T4000








































































Отзывы:

Нет отзывов

Похожие инструкции для EM-PMI540-T4000

Бренд: YOODA Страницы: 6

Бренд: Flux Страницы: 28

Crankcase for Harley-Davidson

Бренд: S&S Cycle Страницы: 12

Бренд: Polini Страницы: 32

Бренд: Nice Страницы: 12

Бренд: Westerbeke Страницы: 65

Бренд: Man Страницы: 64

Бренд: Motorola Страницы: 82

Бренд: BGS technic Страницы: 8

Бренд: Saito Страницы: 5

Бренд: Saito Страницы: 6

Бренд: Robin America Страницы: 43

Бренд: Westerbeke Страницы: 6

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Barrus Страницы: 24

Бренд: New Holland Страницы: 31

Бренд: HPI Racing Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды