Danfoss APP S Series Скачать руководство пользователя | Manualshive

Страница: 8 / 26

background image

Instruction

Disassembling and assembling APP S 2.0-3.5 / APP S 674 2.0-3.5

8

180R9281 / 521B1275 / DKCFN.PI.013.C4.02 / 10.2015

3. Mount new O-ring on port flange and

lubricate with water.

4. Position port flange by aligning pin hole

over guide pin.

6. Lubricate the threads with PTFE lubrication.

Insert screws on the port flange. Tighten

screws to a torque of 30 ± 3 Nm.

5. Carefully press the port flange downwards.

Do not squeeze the O-ring. If the O-ring is

damaged, the pump will leak.

7. Place a 10.5 mm guide pin in the port flange.

«
...
6
7
8
9
10
...
»

Содержание APP S Series



























Отзывы:

Нет отзывов

Похожие инструкции для APP S Series

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: Danfoss Страницы: 38

Бренд: Nachfolger Страницы: 2

Бренд: SAB Страницы: 7

Бренд: ULTIMATE SPEED Страницы: 52

Бренд: Waterous Страницы: 10

Бренд: Daewoo Страницы: 38

Бренд: IDEAL Страницы: 30

Alwayzaire P3062

Бренд: Bestway Страницы: 2

Бренд: Pentair Страницы: 16

Бренд: Sanden Страницы: 48

BlackFin CT-2902BPHP

Бренд: Panduit Страницы: 68

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды