Danfoss APP S Series Скачать руководство пользователя | Manualshive

Страница: 13 / 26

background image

Instruction

Disassembling and assembling APP S 2.0-3.5 / APP S 674 2.0-3.5

13

180R9281 / 521B1275 / DKCFN.PI.013.C4.02 / 10.2015

1. Unscrew centre bolt from swash plate.

2. Remove swash plate, guide pin and O-ring.

4. Lubricate centre bolt thread with a PTFE

lubricant type.

3. Place guide pin and carefully align swash

plate over guide pins.

6. Finally check the surface on the swash

plate for any marks or foreign particles

and place new O-ring.

5. Position the centre bolt and tighten to

12 Nm ± 1 Nm.

3. Disassembling and

assembling of the swash

plate

O-ring

«
...
11
12
13
14
15
...
»

Содержание APP S Series



























Отзывы:

Нет отзывов

Похожие инструкции для APP S Series

Бренд: Qual Craft Страницы: 5

Бренд: Jandy Страницы: 16

Бренд: Daewoo Страницы: 38

Bell & Gossett Domestic 616PF

Бренд: Xylem Страницы: 4

Бренд: IBAIONDO Страницы: 7

FastHeat Digital 14160

Бренд: Kerbl Страницы: 32

Бренд: Rinnai Страницы: 2

Бренд: Pentair Jung Pumpen Страницы: 26

Бренд: Samoa Страницы: 32

Бренд: Launtop Страницы: 22

Бренд: Grundfos Страницы: 153

DrainPress 3200/24 Set

Бренд: T.I.P. Страницы: 68

Бренд: Commercial Electric Страницы: 15

SEASONCON ALP-045C

Бренд: McQuay Страницы: 59

Бренд: Kospel Страницы: 12

LX ACDC/M+K 100 A

Бренд: Logitex Страницы: 18

Бренд: Little Giant Страницы: 16

Бренд: Neptronic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды