Danfoss ADAP-KOOL AK-HP 780 Скачать руководство пользователя | Manualshive

Страница: 72 / 104

background image

72

Heat pump controller RS8GF202 © Danfoss 2015-08

AK-HP 780

If there is no answer from the system unit

If the Status LED does not start flashing faster than normal, the control-

ler has not been installed in the network. The reason for this may be

one of the following:

The controller has been assigned an address out of range

Address 0 cannot be used.
If the system unit in the network is an AKA 243B Gateway only the ad-

dresses between 1 and 10 can be used.

The selected address is already being used by another controller or

unit in the network:

The address setting must be changed to another (vacant) address.

The wiring has not been carried out correctly.

The termination has not been carried out correctly.

The data communication requirements are described in the document:

”Data communication connections to ADAP-KOOL® Refrigeration Con-

trols” RC8AC.

Installation in network

1. Set the address (here, for example 3)

Turn the right-hand address switch so that the arrow will point
at 3.
The arrow of the two other address switches must point at 0.

2. Push the Service Pin

Press down the service pin and keep it down until the Service
Pin LED lights up.

3. Wait for answer from the system unit

Depending on the size of the network it may be up to one
minute before the controller receives an answer as to whether
it has been installed in the network.
When it has been installed the Status LED will start to flash
faster than normal (once every half second). It will continue
with this for about 10 minutes

4. Carry out new login via Service Tool

If the Service Tool was connected to the controller while you
installed it in the network, you must carry out a new login to
the controller via the Service Tool.

The controller has to be remote-monitored via a network. In this net-
work we assign address number 3 to the controller.
The same address must not be used by more than one controller in the
same network.

Requirement to the system unit

The system unit must be a gateway type AKA 245 with software version

6.0 or higher. It is capable of handling up to 119 AK controllers.

Alternatively, it can be an AK-SM 720. It is capable of handling up to 200

AK controllers.

«
...
70
71
72
73
74
...
»

Содержание ADAP-KOOL AK-HP 780









































































































Отзывы:

Нет отзывов

Похожие инструкции для ADAP-KOOL AK-HP 780

Бренд: ABATEC Страницы: 8

Бренд: M&C Страницы: 16

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

Бренд: Samson Страницы: 40

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды