Danfoss ADAP-KOOL AK-HP 780 Скачать руководство пользователя

Страница: 46 / 104

Heat pump controller RS8GF202 © Danfoss 2015-08

AK-HP 780

Configuration - continued

Authorization

1. Go to Configuration menu

Press the orange setup button with the spanner at the bottom
of the display.

2. Select Authorization

3. Change setting for the user ‘SUPV‘

4. Select username and access code

5. Carry out a new login with the user name and the

new access code

You will use this button again and again whenever you want to get to

this display.

On the left-hand side are all the functions not shown yet. There will be

more here the further into the setup we go.

Press the line Authorization to get to the user setup display.

Mark the line with the user name SUPV.
Press the button Change

When the controller is supplied it has been set with standard authoriza-

tion for different user interfaces. This setting should be changed and

adapted to the plant. The changes can be made now or later.

To activate the new settings you must carry out a new login to the con-

troller with the new user name and the relevant access code.

You will access the login display by pressing the padlock at the top left

corner of the display.

This is where you can select the supervisor for the specific system and a

corresponding access code for this person.

The controller will utilize the same language that is selected in the

service tool but only if the controller contains this language. If the

language is not contained in the controller, the settings and readings

will be shown in English.

Содержание ADAP-KOOL AK-HP 780









































































































Результаты поиска

Содержание ADAP-KOOL AK-HP 780

Отзывы:

Похожие инструкции для ADAP-KOOL AK-HP 780

Бренды по названию

Популярные бренды

Danfoss ADAP-KOOL AK-HP 780, Руководство по конструкции

Результаты поиска

Содержание ADAP-KOOL AK-HP 780

Отзывы:

Похожие инструкции для ADAP-KOOL AK-HP 780

Бренды по названию

Популярные бренды