Danfoss ADAP-KOOL AK-HP 780 Скачать руководство пользователя

Страница: 55 / 104

AK-HP 780

Heat pump controller RS8GF202 © Danfoss 2015-08

Setup control of the pump

1. Go to Configuration menu

2. Select pump

3. Set control mode and reference

Press the +-button to go on to the

4. Set values for capacity regulation

Configuration - continued

3 - Reference

Control sensor

S7: Media temperature is used for regulation

Setting

Setting of setpoint

Min reference

Min. permitted reference

Max reference

Max. permitted reference

4 - Capacity control

No pumps

It is only possible to connect to one pump.

Monitoring of the pump

Safety monitoring of the pump. A digital input

must used

Capacity control mode

Select control mode for the pump

On/Off: The pump is connected via a relay outlet

Speed: The pump is controlled via speed control

(frequency converter)

Control type

Choice of control strategy

P-band: The pump capacity is regulated via

P-band control. The P band is configured as

"Proportional band Xp"

PI-Control: The pump capacity is regulated by

the PI controller.

Capacity curve

Choice of capacity curve type

Linear: The same amplification in the entire area

Square: Square curve shape, which gives higher

amplification at higher loads.

VSD start speed

Minimum speed for start of speed control (Must

be configured higher than "VSD Min. Speed %")

VSD min Speed

Minimum speed whereby speed control is cut-

out (low load).

Proportional band Xp

Proportional band for P/PI controller

Integration time Tn

Integration time for PI controller

VSD safety monit.

Choice of safety monitoring of frequency con-

verter. A digital inlet is used for monitoring the

frequency converter.

We select "speed" in our example.

Содержание ADAP-KOOL AK-HP 780









































































































Результаты поиска

Содержание ADAP-KOOL AK-HP 780

Отзывы:

Похожие инструкции для ADAP-KOOL AK-HP 780

Бренды по названию

Популярные бренды

Danfoss ADAP-KOOL AK-HP 780, Руководство по конструкции

Результаты поиска

Содержание ADAP-KOOL AK-HP 780

Отзывы:

Похожие инструкции для ADAP-KOOL AK-HP 780

Бренды по названию

Популярные бренды