DANA SPICER Torque-Hub S6B Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

DANA SPICER Torque-Hub S6B Скачать руководство пользователя страница 16

11

MAIN ASSEMBLY

7.

Lower

first stage carrier (3)

into

hub (1G).

8.

Grease and place one each of

thrust washer (14)

,

thrust bearing (13)

, and

thrust washer (12)

, in that order, onto counterbore on the top of

first stage carrier sub-

assembly (3)

. Make sure the thickest thrust washer (#14) is nearest the carrier.

9.

Place

input gear (8)

into the center of

first stage carrier sub-assembly (3).

CAUTION: Beware sharp edges in the counterbore as “O” ring is installed.

10.

Place

cover (6),

interior side up, on work surface. Grease and place

“O” ring (5)

into the counterbore of

cover (6).

NOTE: The “O” ring can be made to fit the counterbore exactly by stretching its (if it is
too small) or by pinching it together bit by bit (if it is too large) as it is placed into the
counterbore.

11.

Grease one side of

thrust washer (7)

and place it into the counterbore in center

of cover.

12.

Place

cover (6)

onto

ring gear (4)

. Make sure the bolt holes in the ring gear and

cover are aligned. See Diagram 2: Pipe plug timing, on next page.

«
...
14
15
16
17
18
...
»

Содержание SPICER Torque-Hub S6B

























Отзывы:

Нет отзывов