DANA SPICER Torque-Hub S6B Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 24

DANA SPICER Torque-Hub S6B Скачать руководство пользователя страница 11

6

HUB-SPINDLE SUB-ASSEMBLY

NOTE: Make sure the cup sits square with the counterbore before pressing.

1. Set

hub (1G)

on work surface, wide end up. Using bearing cup pressing tool (T-

130717), press

bearing cup (1E)

into the counterbore in the wide end of

hub (1G)

.

NOTE: Make sure the cup sits square with the counterbore before pressing.

2.

Set

hub (1G)

on work surface, small end up. Using bearing cup pressing tool (T-

156792), press

bearing cup (1C)

into the counterbore in the small end of

hub (1G).

3.

Place

bearing cone (1D)

into

bearing cup (1C)

in the small end of

hub (1G).

4.

Using tool (T-156799), press

seal (1B)

into the small end of

hub (1G)

. The closed

face of the seal should be up. Oil

seal (1B).

5.

Place

seal boot (20)

over end of

hub (1G)

. Apply a generous amount of grease

to seal boot.

6.

Apply a light coat of “Never-Seize” to one of the four

pipe plugs (1R)

. Tighten the

one

pipe plug (1R)

into the pipe plug hole in

seal boot (20)

. [Other three

pipe plugs

(1R)

will be installed later.]

7.

Place and press

spindle (1A)

, small end down, into

hub (1G)

.

«
...
9
10
11
12
13
...
»

Содержание SPICER Torque-Hub S6B

























Отзывы:

Нет отзывов