background image

 

 

 

1.  INTRODUCTION 

 
 
In order to mitigate the loss of sensitivity, the gas detection equipment must be calibrated at least once a year, in 
some cases three to four times a year or even more. 
 
The calibration is carried out by the manufacturer or his local representative. 
 
Gas detectors must be calibrated with a calibration gas according to the gas to be detected. 
 
 

Calibration must be performed according to the rules of use and by qualified personnel trained by 
Dalemans exclusively. 

 
 
For further information about the conditions and the procedure of calibration of the gas detectors do not hesitate to 
contact Dalemans : 

 

Tel. : 

+32 (0) 19 • 54 • 52 • 36 

Fax. : 

+32 (0) 19 • 54 • 55 • 34 

Email :  [email protected] 

 
 

In a Dalemans CAN bus system based on OctoBUS 64 central measuring unit, to perform the complete calibration 
procedure of the detectors you need the hand held device 

OctoPRO

 or a computer with 

OctoBUS Configurator

 

software installed. 
 
 

 

 

Figure 1 : OctoPRO 

Figure 2 : OctoBUS Configurator 

 
 

OctoPRO

 and 

OctoBUS Configurator

 are optional features and are delivered by Dalemans only. For any request 

regarding to these two products please contact Dalemans. 
 
The following instructions give the calibration procedure with 

OctoPRO

 device. For more information about the use 

of the 

OctoPRO

 device please refer to the related instruction manual. 

 
The calibration procedure by mean of a computer is described in the 

OctoBUS Configurator

 Instruction Manual. 

Can Bus Gas Detectors - 

Man-CanDetectors-Cal-En-V10.doc

 

C lib

ti

Содержание octoPRO












Отзывы: