Daktronics VF-2400 GEN 2 Series Скачать руководство пользователя | Manualshive

Страница: 15 / 42

background image

Mechanical Installation

9

Section 3:

Mechanical Installation

3.1 Display Lifting

The top of the display is equipped with several

5

/

8

" eyebolts for lifting the display. Lift the

display using a lifting bar. Use every eyebolt, and maintain a 90° lifting angle as shown in

. The eyebolts may fail if this is not done.

The eyebolts are designed to carry only the weight of the display cabinet. Do not lift the

mounting structure or other additional weight. Do not permanently support the display with

the eyebolts. Contact Daktronics with additional questions about display lifting.

3.2 Setting the Display on the Ground

Several wood 2 x 4 transportation skids are attached to the bottom of the display. If setting

the display on concrete, no additional supports are needed.

If setting the display on grass, place the supports directly under the transportation skids.

Failure to use the transportation skids may result in damage to the display.

Figure 5: Correctly Lifting the Display

«
...
13
14
15
16
17
...
»

Содержание VF-2400 GEN 2 Series











































Отзывы:

Нет отзывов

Похожие инструкции для VF-2400 GEN 2 Series

Бренд: Daktronics Страницы: 37

Бренд: 3M Страницы: 4

Бренд: I-Inc Страницы: 1

Бренд: Edge10 Страницы: 1

Бренд: XP-PEN Страницы: 12

Бренд: Eizo Страницы: 4

GOT3187W-881-PCT

Бренд: AXIOMTEK Страницы: 56

Бренд: Tatung Страницы: 21

Бренд: Mottura Страницы: 40

Бренд: NEOFYTE Страницы: 21

VA2016W - 20" LCD Monitor

Бренд: ViewSonic Страницы: 23

Planar LookThru LO55

Бренд: Leyard Страницы: 23

Бренд: NCR Страницы: 6

Бренд: VTech Страницы: 2

Бренд: VTech Страницы: 2

Бренд: ViewSonic Страницы: 2

Бренд: Daewoo Страницы: 44

Бренд: Idis Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды