background image

DAKTRONICS AQUATICS MAINTENANCE CHECKLIST 

 

DD3691471  072017 

201 Daktronics Drive  PO Box 5128  Brookings, SD 57006-5128 

 

800-325-8766  605-692-0200  fax 605-697-4700 

www.daktronics.com  email [email protected] 

 

 

 

Use this checklist to ensure your Daktronics Aquatic Systems is operating properly and looking 

as good as possible. We recommend completing these checks every six months, or whenever 

you suspect an issue with your display. In most circumstances, the owner or operator of the 

display should be able to complete this checklist. For additional information and 

troubleshooting resources, see the appropriate manual for your display. 

 

 

Checklist Task 

Key Points 

 

    

 

    

 

   

 

OmniSport 2000 

o

 

Visually inspect the OmniSport for damage/corrosion. (indicators, switches, 

knobs, and connections). 

o

 

Ensure keypad buttons are all functional. 

o

 

Verify that thermal paper is installed in printer location and  

feeds/prints correctly. 

o

 

Power up OmniSport console to verify firmware is up to date  

(update if needed). 

 

Must be newer than 8.3.27 to update in the field. 

o

 

Perform Mock swim race after completing checklist to verify all inputs and 

outputs are working (including scoreboard/RTD data). 

 

 

OmniSport 2000 Manual=ED-13312

 

 

   

  

 

 

 

On-deck Equipment  

(lane modules) 

o

 

Visually inspect lane modules for damage/corrosion. (connections, 

connector, and cable). 

o

 

If equipment shows signs of corrosion, train customer (if available) proper 

cleaning of lane modules using the brass brush (TH-1024/TH-1025) and 

silicone grease (LU-1002). 

 

 

How to Test a Daktronics Lane Module

 

 

      

 

 

 

 

In-deck Equipment 

(deck plates) 

o

 

Visually inspect all deck plates for damage/corrosion.  

(connections, connector, and cable). 

o

 

If equipment shows signs of corrosion, train customer (if available) proper 

cleaning of lane modules using the brass brush (TH-1024/TH-1025) and 

silicone grease (LU-1002). 

OmniSport 2000 Manual=ED-13312

 

 

     

  

 

 

Содержание Aquatics







Отзывы: